The abbreviation used in place of the word high potential is hipot. This term is used in reference to a given group of instruments used for testing electrical safety in electric products. Hipot tester is used to verify the electrical insulation in various wired assemblies including appliances and finished cables. Some of these wired assemblies are printed circuit boards, transformers, and electric motors.
In many cases, after the assembling/manufacturing of an appliance/product some current leakage of some level occurs. The interior of the product contains internal capacitance and voltages that often cause this minimal current leakage. It is normal for all devices to experience this leakage. However, in some scenarios, the current leakage may too high that it should be due to certain reasons.
Excess leakage may be caused by break down of insulation in the product, design flaws or many other causes. Such flaws usually lead to excessive current leaking and may cause electrical shock to anyone that comes in contact with the faulty product. The importance of a hipot test is to verify and ensure that the product is sufficiently insulated so as not to cause shock to the operator.
Dielectric Withstanding Voltage, DWV, is another term used in reference to the hipot test. At the time of the test, a high voltage is applied between the conductors that carry current in the product and its metallic shielding. Upon completion, there will exist a resultant current that makes its way through the insulator material. The term used for this current is leakage current and is tested using a high potential tester.
One major assumption is made in hipot testing. The assumption is that by applying excessive voltage, the insulation of the product should break, and if it does not, then the device should work fine under normal conditions. The appliance is supposed to be resilient against normal voltage, which is often applied in ordinary everyday use of most devices. It is this assumption that gives rise to the name Dielectric Withstanding Voltage.
The test is aimed at stressing the insulator used in the appliance. Apart from stressing the insulator material, however, the test is additionally used to identify workmanship flaws in the product. The most critical monitored workmanship elements are minute spaces existing between the earth ground and current-carrying conductors. In ordinary environment of operation, shock, humidity, contaminants, shock, and dirt may fill these spaces.
When these small gaps close, the flow of current is enabled. This flow of current can be a major electrical hazard. Prior to product release into the market, it must be tested verify that such hazards cannot occur. The only applicable method that can be used in the detection of this type of defects is DWV. This is true in spite of there being other viable methods.
Manufacturers use high potential testers to do the verification of electrical insulation. Often, this simple electric device comprises of a switching matrix, current meter, and a source for the high voltage. All the points located on the cable are connected to the high-voltage source and the current meter through the matrix. Including a display and a microcontroller helps to automate the testing process.
In many cases, after the assembling/manufacturing of an appliance/product some current leakage of some level occurs. The interior of the product contains internal capacitance and voltages that often cause this minimal current leakage. It is normal for all devices to experience this leakage. However, in some scenarios, the current leakage may too high that it should be due to certain reasons.
Excess leakage may be caused by break down of insulation in the product, design flaws or many other causes. Such flaws usually lead to excessive current leaking and may cause electrical shock to anyone that comes in contact with the faulty product. The importance of a hipot test is to verify and ensure that the product is sufficiently insulated so as not to cause shock to the operator.
Dielectric Withstanding Voltage, DWV, is another term used in reference to the hipot test. At the time of the test, a high voltage is applied between the conductors that carry current in the product and its metallic shielding. Upon completion, there will exist a resultant current that makes its way through the insulator material. The term used for this current is leakage current and is tested using a high potential tester.
One major assumption is made in hipot testing. The assumption is that by applying excessive voltage, the insulation of the product should break, and if it does not, then the device should work fine under normal conditions. The appliance is supposed to be resilient against normal voltage, which is often applied in ordinary everyday use of most devices. It is this assumption that gives rise to the name Dielectric Withstanding Voltage.
The test is aimed at stressing the insulator used in the appliance. Apart from stressing the insulator material, however, the test is additionally used to identify workmanship flaws in the product. The most critical monitored workmanship elements are minute spaces existing between the earth ground and current-carrying conductors. In ordinary environment of operation, shock, humidity, contaminants, shock, and dirt may fill these spaces.
When these small gaps close, the flow of current is enabled. This flow of current can be a major electrical hazard. Prior to product release into the market, it must be tested verify that such hazards cannot occur. The only applicable method that can be used in the detection of this type of defects is DWV. This is true in spite of there being other viable methods.
Manufacturers use high potential testers to do the verification of electrical insulation. Often, this simple electric device comprises of a switching matrix, current meter, and a source for the high voltage. All the points located on the cable are connected to the high-voltage source and the current meter through the matrix. Including a display and a microcontroller helps to automate the testing process.
About the Author:
We have all the detailed specifications on hipot tester the best on our related homepage. Simply use this link to reach the main website at http://www.rossengineeringcorp.com/products/measurement/ac-dc-digital-hipots.html.
No comments:
Post a Comment